search
Menu
 

Heat Exchanger Tube Inspection

  • Home
  • Heat Exchanger Tube Inspection

Heat Exchanger Tube Inspection Techniques: An Overview

heat exchanger tube inspection techniques

Making a choice between the various heat exchanger tube inspection techniques centers on two things: timing and access. In most cases, the inspection occurs because of an outage, with the goal being to get back online as quickly as possible. Ideally, inspection techniques will allow for the rapid discovery and resolution of flaws while working efficiently with ferromagnetic and non-ferromagnetic alloys.

A missed flaw could result in more extended periods of downtime that lead to expensive losses. Accuracy is vital in ensuring proper resolution. Typical heat exchanger tube inspection techniques include eddy current, remote field eddy current, internal rotating ultrasonic, flux leakage, and laser optic. 

Common Challenges in Heat Exchanger Inspections 

heat exchanger tube inspection techniques

Heat exchanger tube inspections have to be sophisticated due to some issues with the material, form, and purpose of tests. It can be challenging to garner accurate NDT results due to:

  • Time or budgetary constraints: At times, only a sample of the heat exchanger tubing is under review due to time or cost constraints. Technicians will target the area most likely to be the cause of problems. 
  • Manual, inconsistent process: Current manual methods might not deliver the confidence needed across a full inspection campaign. Data acquisition and analysis can be spread across multiple inspection crews leading to the possibility of inconsistencies and the commonly asked question: “Are we capturing all our flaws?” 
  • Reactive testing: Routine reviews of heat exchanger tubes are less of a concern than more frequent inspections due to malfunction. It’s possible to find flaws that aren’t directly related to the malfunction and mistakenly assume they’re the ones that require resolution. When this fails to resolve the issue, the entire inspection must start again. 
  • Complex inspection techniques: There are no valid heat exchanger tube inspection techniques for non-specialists. All require sophisticated technology, like array probes, and a deep understanding of NDT and the data it recovers. It can be challenging to find the right personnel to complete the task. 
  • Turnaround: Some NDT inspection techniques can require extensive preparation and are slow-moving. Facilities are usually in a rush to return their equipment to functional status, so such delays are concerning. Furthermore, final analysis and reporting can lag the acquisition process by days, delaying dispositioning of the component.  

Of course, these aren’t the only issues to consider in managing heat exchanger tube inspections. It’s vital to consider the different types of flaws and their suspected location to streamline testing. 

Pre Heat Exchanger Tube Inspection Considerations 

Oftentimes, before conducting a heat exchanger tube inspection, the technician will have an idea of what they’re looking for. The type of flaw and its location will determine what heat exchanger tube inspection technique the technician leverages. 

Defect Types Location
  • Corrosion: While virtually all corrosion types could come into play, the most obvious culprit is usually steam corrosion. 
  • Cracking: Cracking can occur due to one-time damage or overtime as pressure weakens certain parts of the tube. It can be particularly challenging to locate cracking within bends.  
  • Pitting: This is a localized form of corrosion that leaves small holes within the tube. The smaller these holes, the harder they are to locate. Tiny pinholes are incredibly challenging to find. 
  • Thinning: The original wall thickness can thin due to pressure over time. Thinning is particularly prevalent in bends, which are usually under more stress than straight portions of the tube.  
  • Dents: Dents can occur due to corrosion and are often precursors to more severe cracking or warping. 
  • Surface: Surface flaws are probably the easiest to locate in a tube as most detection methods will help find them. 
  • In welds: Flaws in welds can run the gamut from hydrogen cracks to large pores or poor fusion. The ability to locate even the smallest imperfection in these locations is paramount.  
  • Tubesheet or plates: Not all NDT methods are good for locating flaws within tubesheets or plates. Issues between plates or at the tubesheet expansion transition zone are at particularly high risk for cracking. 
  • Within the wall: Issues within the wall can occur near the inner diameter or closer to the outer diameter. Not all NDT methods can penetrate entirely through the wall, so having an understanding of the defects relative location to the interior or exterior of the tube is critical. 

A basic understanding of the type of flaw and its location will help the technician choose the right technique. Some standard heat exchanger tube inspection techniques are ideal for corrosion, while others are best for discovering cracks in bends or tubesheets and plates. With the right knowledge, the inspector will choose the technique to locate the flaw at the first pass and get the machinery back online faster. 

5 Heat Exchanger Tube Inspection Techniques

Heat exchanger inspections are varied for a reason. Technicians deal with different kinds of materials, flaws, and sizes, all of which may require a different inspection method. In many cases, more than one inspection method will help to locate problems. 

Learn how to improve heat exchanger tube inspection techniques by watching our webinar! 

#1: Eddy Current Testing (ECT)

A probe with a single coil—or ideally, an array of them—sends an electrical pulse throughout the component to be examined. The probe pulls through the tube, recording readings in the electrical field along the way. This method offers multiple benefits, making it one of the more popular techniques.

Pros Cons
  • Testing is relatively rapid, though not as fast as standard eddy current 
  • Is ideal for testing for corrosion and wear over more considerable distancesThe use of flexible probes allows this test to be administered even over bends and corners 
  • It allows for broader diameter testing than standard eddy current 
  • Challenging to detect smaller flaws or minimal erosion 
  • As with standard eddy current, equipment and tests can be costly 
  • Defects in plates or tubesheets may not be as easy to detect The tube will require cleaning before testing 
  • An experienced, knowledgeable technician must complete tests

#2: Remote Field Eddy Current Testing (RFET) 

RFET is similar to standard eddy current, where an electrical pulse creates a field. However, in this case, a transmission coil and receiver coil work together to transmit signals back and forth. This process allows for testing over greater distances, rather than being limited to smaller sample areas. 

Pros Cons
  • Testing is relatively rapid, though not as fast as standard eddy current 
  • Is ideal for testing for corrosion and wear over more considerable distancesThe use of flexible probes allows this test to be administered even over bends and corners 
  • It allows for broader diameter testing than standard eddy current 
  • Challenging to detect smaller flaws or minimal erosion 
  • As with standard eddy current, equipment and tests can be costly 
  • Defects in plates or tubesheets may not be as easy to detect The tube will require cleaning before testing 
  • An experienced, knowledgeable technician must complete tests

#3: Internal Rotating Inspection System (IRIS) 

An internal rotating inspection system uses sound, rather than electricity, to locate flaws or discontinuities within a tube. Water fills the tube as a rotating probe moves from one end to another. Data is collected and recorded. 

Pros Cons
  • Highly accurate results, especially when detecting metal loss 
  • Is an excellent follow up to RFET or ECTAllows end-to-end inspections 
  • Works for both ferromagnetic and non-ferromagnetic materials 
  • Very time-consuming as the probe must be pulled through slowly
  • Water is required throughout the entirety of the test
  • No ability to detect circumferential cracks or bend defects, which is why it’s often used with RFET
  • Only highly skilled technicians can engage this method 

#4: Transverse Field Inspection (TFI)

TFI, often called magnetic flux leakage testing, is a process of leveraging magnets in testing for pitting, cracks, and corrosion in tubes. The steel is magnetized and then evaluated for magnetic leaks, which occur in areas of thinning or deterioration. 

Pros Cons
  • Can inspect larger tubes than most other methods
  • Useable even under extreme field conditions 
  • Offers end sheet and plate flaw detection 
  • May be better able to detect other flaws like dents, wrinkles, and buckles that other methods cannot
  • Primarily used for corrosion detection as flaws must be large to be detectable
  • Can be time-consuming as the test results will depend on the speed of the inspection
  • Only suitable for ferromagnetic materials 
  • Cannot assess u-bends or determine discontinuity size 

#5: Laser Inspection 

A laser beam is projected onto the inspected tube. It maps the surface and penetrates to measure inside the wall as well. The laser rotates as the probe moves through the tube to provide a complete internal map. Light displacement measures flaws and discontinuities. 

Pros Cons
  • Offers real-time inspection 
  • Ideal for locating deformations and corrosion inside the tube 
  • Allows for the inspection of very large tubes 
  • High data point sampling allows for inspections of long tubes 
  • Shiny surfaces can interfere with accurate readings 
  • Limited to detecting certain types of flaws and cannot provide wall thickness measurements
  • Equipment is sensitive and can easily be broken 

Eddy current based techniques are perhaps the most popular heat exchanger tube inspection methods because of their versatility. When seeking out a particular flaw, like corrosion or wall thinning, it may be wiser to choose a technique more adept at locating these very specific issues. Regardless of the method selected, there is one more essential facet to inspections that technicians must consider. That’s the software that helps them make sense of the data collected. 

Choosing the Right Analysis Method to Increase Accuracy 

technician demostrating heat exchanger tube inspection techniques

The heat exchanger tube inspection technique chosen is only as good as the analysis of the data it garners. The possibility of human error in reviewing this data is significant and can result in wasted time, funds, and more extended equipment downtime. Leveraging automated analysis in heat exchange inspections can eliminate human error by allowing computer software to do the more complex calculations and data reviews involved in assessments. 

Consider eddy current testing. Reduced inspection scope, limited data tracking, and the inspection’s complexity can result in less effective readings. Automating and refining the process of both data acquisition and analysis increases productivity and enhances results. Specifically, it allows for the faster completion of tests, so plants can complete more and improve their turnaround rates. 

Automation can also help technicians leverage more complex but accurate solutions. Eddy current testing works best with an array probe, but this garners a lot of data which can be challenging to categorize and understand. Automated solutions aggregate this data and help to provide interpretations based on it. 

Finally, technicians have varying experience levels. Results can differ from inspector to inspector. Automation standardizes results and helps to even the playing field for all technicians. Readings are consistent no matter who completes them. 

Human error is the most significant barrier to accuracy in heat exchanger tube inspection techniques. Leveraging intelligent software—such as the RevospECT HX Pro by Zetec—to analyze data collected improves the probability of accuracy and speeds completion of these necessary tests. This process eliminates downtime and helps plants get machinery back online faster, with a lower risk of reoccurring problems.  

Zetec offers eddy current inspection and highly detailed, automated software for evaluating results and improving output. Visit our contact page to learn more about our heat exchanger tube inspection techniques.